Enhanced grip and performance

PIP is constantly bringing new innovations to our general purpose glove line. With a variety of superior coating and grip technologies, combined with comfortable liner materials, these products improve performance without sacrificing dexterity and comfort.

SHOWING 1-36 OF 109 ITEMS
1 of 4
Polyester with Nitrile Grip

Boss®

Hi-Vis Seamless Knit Polyester Glove with Nitrile Coated Smooth Grip on Palm & Fingers

1UH7802

  • Seamless Knit Glove
  • Hi-Vis Yellow Polyester Shell
  • 13 Gauge
  • Black Nitrile Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-2XL
  • PACKED: 144 Pair/Case

2121

EN 388 2016 Results: 2121XX

Abrasion: 2
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Polyester with Nitrile Grip

Boss®

Seamless Knit Polyester Glove with Double-Dipped Nitrile Coated MicroSurface Grip on Palm & Fingers

1UH7820

  • Seamless Knit Glove
  • Black Polyester Shell
  • 13 Gauge
  • Black Nitrile Coated MicroSurface Grip
  • Double Dipped
  • Palm & Fingers
  • Knit Wrist
  • SIZES: S-3XL
  • PACKED: 144 Pair/Case

4121

EN 388 2016 Results: 4121XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Nitrile Grip

Boss®

Seamless Knit Nylon Glove with Premium Nitrile Coated MicroSurface Grip on Palm & Fingers

1UH7830

  • Seamless Knit Glove
  • Gray Nylon Shell
  • 15 Gauge
  • Premium Black Nitrile MicroSurface Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-3XL
  • PACKED: 144 Pair/Case

4131

EN 388 2016 Results: 4131XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
ECO Series GP Sustainable Fiber Gloves

G-Tek® ECO Series™

Seamless Knit Recycled Yarn / Spandex Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

31-131R

  • Seamless Knit Glove
  • 13G White Recycled Yarn Shell
  • Gray PU Coating
  • Palm & Fingertips
  • Passes Global Recycled Standard
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 10 Dozen/Case

3131

EN 388 2016 Results: 3131XX

Abrasion: 3
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Beginning of Life – Made from Recycled Materials

PIP® has taken our innovative platform to the next level, we use recycled P.E.T. water bottles – shredded and extruded as a fiber creating a comfortable and cool material as well as recycled polyester yarns used to create yarns for gloves and apparel.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
ECO Series GP Sustainable Fiber Gloves

G-Tek® ECO Series™

Seamless Knit Recycled Yarn / Spandex Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

31-330R

  • Seamless Knit Glove
  • 13G White Recycled Yarn Shell
  • Gray Nitrile Foam Coating
  • Palm & Fingertips
  • Passes Global Recycled Standard
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 10 Dozen/Case

4121

EN 388 2016 Results: 4121XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Beginning of Life – Made from Recycled Materials

PIP® has taken our innovative platform to the next level, we use recycled P.E.T. water bottles – shredded and extruded as a fiber creating a comfortable and cool material as well as recycled polyester yarns used to create yarns for gloves and apparel.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
ECO Series GP Sustainable Fiber Gloves

G-Tek® ECO Series™

Seamless Knit Recycled Yarn / Spandex Blended Glove with Nitrile Coated MicroSurface Grip on Palm & Fingers

31-530R

  • Seamless Knit Glove
  • 13G White Recycled Yarn Shell
  • Dark Gray Nitrile Microsurface Coating
  • Passes Global Recycled Standard
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 10 Dozen/Case

4121

EN 388 2016 Results: 4121XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Beginning of Life – Made from Recycled Materials

PIP® has taken our innovative platform to the next level, we use recycled P.E.T. water bottles – shredded and extruded as a fiber creating a comfortable and cool material as well as recycled polyester yarns used to create yarns for gloves and apparel.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Specialty PVC Blends on Gloves

G-Tek®

Seamless Knit Nylon Glove with Air-Infused PVC Coating on Palm & Fingers - DISCONTINUED

32-747

  • Seamless Knit Glove
  • Black Nylon Shell
  • 15 Gauge
  • Black Air-Infused PVC Grip
  • Palm & Fingertips
  • Now w/ DISCOUNTED PRICING!
  • SIZES: XS-XL
  • PACKED: 12 Dozen/Case

3131

EN 388 2016 Results: 3131X

Abrasion: 3
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-1
ANSI Abrasion Level: 1

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare

G-Tek®

Seamless Knit Polyester Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-105-AP

  • G-Tek®
  • Urethane Coated Palm and Fingers
  • White Urethane
  • White Polyester
  • SIZES: XS-2XL
  • PACKED: 144 Pair/Case

3121

EN 388 2016 Results: 3121XX

Abrasion: 3
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

Compare
Polyester with Polyurethane Grip

PIP®

Seamless Knit Polyester Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-115

  • Seamless Knit
  • White Polyester Shell
  • 13 Gauge
  • White Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

3121

EN 388 2016 Results: 3121X

Abrasion: 3
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Polyurethane Grip

G-Tek®

Seamless Knit Nylon Blend Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-125

  • Seamless Knit
  • White Nylon Blend Shell
  • 13 Gauge
  • White Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Polyurethane Grip

G-Tek®

Heavy Weight Seamless Knit Nylon Glove with Extra Thick Polyurethane Coated Flat Grip on Palm & Fingers

33-325

  • Heavy Weight Seamless Knit
  • Black Nylon Shell
  • 13 Gauge
  • Extra Thick Black Polyurethane Flat Grip
  • Palm & Fingertip
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Polyester with Polyurethane Grip

G-Tek®

Hi-Vis Seamless Knit Polyester Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-425LY

  • Seamless Knit
  • Hi-Vis Yellow Polyester Shell
  • 13 Gauge
  • Hi-Vis Yellow Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

3131A

EN 388 2016 Results: 3131AX

Abrasion: 3
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test): A
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Polyester with Polyurethane Grip

G-Tek®

Hi-Vis Seamless Knit Polyester Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-425OR

  • Seamless Knit
  • Hi-Vis Orange Polyester Shell
  • 13 Gauge
  • Hi-Vis Orange Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

3131A

EN 388 2016 Results: 3131AX

Abrasion: 3
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test): A
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-2
ANSI Abrasion Level: 2

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Polyester with Polyurethane Grip

PIP®

Seamless Knit Polyester Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-B115

  • Seamless Knit
  • Black Polyester Shell
  • 13 Gauge
  • Black Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

3121

EN 388 2016 Results: 3121X

Abrasion: 3
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Polyurethane Grip BEST SELLER

G-Tek®

Seamless Knit Nylon Blend Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-B125

  • Seamless Knit
  • Black Nylon Blend Shell
  • 13 Gauge
  • Black Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Polyurethane Grip

G-Tek®

Seamless Knit Nylon Blend Glove with Polyurethane Coated Flat Grip on Palm & Fingers - Vend-Ready

33-B125V

  • Seamless Knit
  • Black Nylon Blend Shell
  • 13 Gauge
  • Black Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • Vend Packed
  • SIZES: XS-2XL
  • PACKED: 300 Pair/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Polyester with Polyurethane Grip

PIP®

Seamless Knit Polyester Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-G115

  • Seamless Knit
  • Gray Polyester Shell
  • 13 Gauge
  • Gray Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

3121

EN 388 2016 Results: 3121X

Abrasion: 3
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Polyurethane Grip BEST SELLER

G-Tek®

Seamless Knit Nylon Blend Glove with Polyurethane Coated Flat Grip on Palm & Fingers

33-G125

  • Seamless Knit
  • Gray Nylon Blend Shell
  • 13 Gauge
  • Gray Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-3XL
  • PACKED: 25 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Polyurethane Grip

G-Tek®

Seamless Knit Nylon Blend Glove with Polyurethane Coated Flat Grip on Palm & Fingers - Vend-Ready

33-G125V

  • Seamless Knit
  • Gray Nylon Blend Shell
  • 13 Gauge
  • Gray Polyurethane Flat Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • Vend Packed
  • SIZES: XS-3XL
  • PACKED: 300 Pair/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Polyurethane Grip

G-Tek® Touch

Seamless Knit Nylon/Polyester Glove with Polyurethane Coated Flat Grip on Palm & Fingers - Touchscreen Compatible

33-GT125

  • Seamless Knit
  • Gray Nylon/Polyester 13G Shell
  • Gray Polyurethane Flat Grip
  • Palm & Fingers
  • Touchscreen Compatible
  • Silicone Free
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 25 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with Polyurethane Grip BEST SELLER

G-Tek® VR-X™

Seamless Knit Nylon Glove with Polyurethane Advanced Barrier Protection Coating on Full Hand – Touchscreen Compatible

33-VRX180

  • Seamless Knit
  • Blue 18G Nylon Shell
  • Black Full Dip VR-X PU Coating
  • Liquid Proof
  • AQL 4.0
  • Touchscreen
  • Silicone Free
  • ESD Safe
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case

3111

EN 388 2016 Results: 3111XX

Abrasion: 3
Cut (Coupe Test): 1
Tear: 1
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-1
ANSI Abrasion Level: 1

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 2

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

ESD Safe

ESD is an acronym for electrostatic discharge. This discharge is the rapid transfer of static between two different objects. Although ESD doesn’t typically cause harm to the human body - you might only experience it as a small, surprising shock - it can cause extensive damage to electrical equipment and sensitive instruments. This damage may either be permanent, causing the device to malfunction (known as a catastrophic failure), or it may occur on a smaller scale that would be difficult to detect before the device is sent out for service (known as latent defect).

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with Nitrile Grip

G-Tek®

Seamless Knit Nylon Glove with Nitrile Coated Smooth Grip on Palm & Fingers

34-225

  • Seamless Knit Glove
  • White Nylon Shell
  • 13 Gauge
  • Gray Solid Nitrile Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: XS-XL
  • PACKED: 25 Dozen/Case

4121

EN 388 2016 Results: 4121X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Polyester with Nitrile Grip

PIP®

Seamless Knit Polyester Glove with Nitrile Coated MicroSurface Grip on Palm & Fingers

34-300

  • Seamless Knit Glove
  • Gray Polyester Shell
  • 13 Gauge
  • Black Nitrile MicroSurface Grip
  • Palm & Fingertips
  • Unbranded
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case

4121

EN 388 2016 Results: 4121X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Polyester with Nitrile Grip NEW

G-Tek®

Seamless Knit Polyester Glove with Nitrile Coated Foam Grip on Palm & Fingers - 15 Gauge

34-315

  • Seamless Knit Glove
  • Navy Blue Polyester Shell
  • 15 Gauge
  • Black Nitrile Coated Foam Grip
  • Palm & Fingertips
  • Silicone Free
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case

4121

EN 388 2016 Results: 4121XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 2

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Nitrile Grip

G-Tek®

Seamless Knit Nylon Glove with Nitrile Coated MicroSurface Grip on Palm & Fingers - 18 Gauge

34-400

  • Seamless Knit Glove
  • Green Nylon Shell
  • 18 Gauge
  • Black Nitrile Coated MicroSurface Grip
  • Palm & Fingertips
  • Knit Wrist
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case

4111

EN 388 2016 Results: 4111X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 1
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-1
ANSI Abrasion Level: 1

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Nitrile Grip

G-Tek®

Seamless Knit Nylon Glove with Nitrile Coated MicroSurface Grip on Palm & Fingers

34-500

  • Seamless Knit Glove
  • Blue Nylon Shell
  • 13 Gauge
  • Black Nitrile Coated MicroSurface Grip
  • Palm & Fingertips
  • Knit Wrist
  • Pair Bagged
  • SIZES: XXS-2XL
  • PACKED: 12 Dozen/Case

4121

EN 388 2016 Results: 4121XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-2
ANSI Abrasion Level: 2

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with Nitrile Grip

G-Tek®

Seamless Knit Nylon Glove with Nitrile Coated MicroSurface Grip on Palm & Fingers - Vend-Ready

34-500V

  • Seamless Knit Glove
  • Blue Nylon Shell
  • 13 Gauge
  • Black Nitrile Coated MicroSurface Grip
  • Palm & Fingertips
  • Knit Wrist
  • Vend Packed
  • SIZES: XS-2XL
  • PACKED: 144 Pair/Case

4121

EN 388 2016 Results: 4121XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-2
ANSI Abrasion Level: 2

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
Nylon with NeoFoam Grip

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm & Fingers - Light Duty

34-600

  • Seamless Knit
  • Blue 15G Nylon Shell
  • Black NeoFoam Grip
  • Palm & Fingers
  • Touchscreen
  • Complies with FDA 21 CFR
  • Silicone Free
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case

4121

EN 388 2016 Results: 4121XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with NeoFoam Grip

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm, Fingers & Knuckles - Light Duty - DISCONTINUED

34-603

  • Seamless Knit
  • Blue 15G Nylon
  • Black NeoFoam Grip
  • 3/4 Dip
  • Touchscreen
  • Silicone Free
  • Pair Bagged
  • Now w/ DISCOUNTED PRICING!
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case

4121

EN 388 2016 Results: 4121X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with NeoFoam Grip

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm, Fingers & Knuckles - Medium Duty - DISCONTINUED

34-608

  • Seamless Knit
  • Earth Tone 15G Nylon
  • Double Strand
  • Black NeoFoam Grip
  • 3/4 Dip
  • Touchscreen
  • Pair Bagged
  • Now w/ DISCOUNTED PRICING!
  • SIZES: S-2XL
  • PACKED: 12 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with NeoFoam Grip

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm & Fingers - Micro Dotted Grip

34-640

  • Seamless Knit
  • Blue 15G Nylon Shell
  • Black NeoFoam Grip
  • Micro Dotted Palm & Fingers
  • Touchscreen
  • Complies with FDA 21 CFR
  • Pair Bagged
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case

4121

EN 388 2016 Results: 4121X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with NeoFoam Grip

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm, Fingers & Knuckles - Micro Dotted Grip - DISCONTINUED

34-643

  • Seamless Knit
  • Blue 15G Nylon
  • Black NeoFoam Grip
  • 3/4 Dip and Micro Dotted
  • Touchscreen
  • Pair Bagged
  • Now w/ DISCOUNTED PRICING!
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case

4121

EN 388 2016 Results: 4121X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with NeoFoam Grip

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm & Fingers - Micro Dotted Grip - DISCONTINUED

34-645

  • Seamless Knit
  • Earth Tone 15G Nylon
  • Double Strand
  • Black NeoFoam Grip
  • Micro Dotted Palm & Fingers
  • Touchscreen
  • Now w/ DISCOUNTED PRICING!
  • SIZES: S-2XL
  • PACKED: 12 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-1
ANSI Abrasion Level: 1

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare
Nylon with NeoFoam Grip

G-Tek® NeoFoam®

Seamless Knit Nylon Glove with NeoFoam® Coated Palm, Fingers & Knuckles - Micro Dotted Grip - DISCONTINUED

34-648

  • Seamless Knit
  • Earth Tone 15G Nylon
  • Double Strand
  • Black NeoFoam Grip
  • 3/4 Dip & Micro Dotted
  • Touchscreen
  • Now w/ DISCOUNTED PRICING!
  • SIZES: S-2XL
  • PACKED: 12 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Compare

G-Tek® GP™

Seamless Knit Nylon Glove with Nitrile Coated Foam Grip on Palm & Fingers

34-810-AP

  • Foam Nitrile Coated Palm and Finger Tips
  • White Nylon Liner
  • Gray Foam Nitrile
  • SIZES: S-XL
  • PACKED: 240 Pair/Case

4121

EN 388 2016 Results: 4121XX

Abrasion: 4
Cut (Coupe Test): 1
Tear: 2
Puncture: 1
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

Compare
Nylon with Nitrile Grip

G-Tek®

Seamless Knit Nylon Glove with Nitrile Coated Smooth Grip on Palm & Fingers

34-C229

  • Seamless Knit Glove
  • White Nylon Shell
  • 13 Gauge
  • Blue Solid Nitrile Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-XL
  • PACKED: 25 Dozen/Case

4131

EN 388 2016 Results: 4131X

Abrasion: 4
Cut (Coupe Test): 1
Tear: 3
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Compare
SHOWING 1-36 OF 109 ITEMS
1 of 4
pin Rep Finder
Compare ()
Clear All Compare
Okay, Got it.
X

ORDER SAMPLE

X

GET FIELD TRIAL