Leaders in
Hand Protection
and PPE

BROWSE ALL PRODUCTS
SHOWING 1-13 OF 13 ITEMS
1 of 1
Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

19-D310

  • G-Tek 3GX with Dyneema Diamond Technology
  • White Knit with Gray PU Palm & Fingertip Coating
  • EN Cut Level 4
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4442C

EN 388 2016 Results: 4442CX

Abrasion: 4
Cut (Coupe Test): 4
Tear: 4
Puncture: 2
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Latex Coated Crinkle Grip on Palm & Fingers - Medium Weight

19-D313

  • G-Tek 3GX
  • White Dyneema Diamond
  • Blue Latex Crinkle Coated Palm
  • EN Cut Level 5
  • SIZES: S-XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

3544D

EN 388 2016 Results: 3544DX

Abrasion: 3
Cut (Coupe Test): 5
Tear: 4
Puncture: 4
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves BEST SELLER

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

19-D318

  • G-TEK 3GX
  • 18 Gauge Dyneema
  • Blue Knit with Black Polyurethane
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

3342B

EN 388 2016 Results: 3342BX

Abrasion: 3
Cut (Coupe Test): 3
Tear: 4
Puncture: 2
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-2
ANSI Abrasion Level: 2

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

19-D320

  • G-Tek 3GX with Dyneema Diamond Technology
  • Gray/Black Knit with Gray PU Palm and Fingertip Coating
  • EN Cut Level 4
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4442C

EN 388 2016 Results: 4442CX

Abrasion: 4
Cut (Coupe Test): 4
Tear: 4
Puncture: 2
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

19-D325

  • G-Tek 3GX
  • White Dyneema Diamond
  • 13 Gauge
  • White Polyurethane Coated Palm
  • EN Cut Level 5
  • SIZES: XXS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4541C

EN 388 2016 Results: 4541CX

Abrasion: 4
Cut (Coupe Test): 5
Tear: 4
Puncture: 1
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

19-D326

  • G-Tek 3GX
  • S&P Dyneema Diamond
  • Black Polyurethane Coated Palm
  • EN Cut Level 4
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4442C

EN 388 2016 Results: 4442CX

Abrasion: 4
Cut (Coupe Test): 4
Tear: 4
Puncture: 2
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

19-D327

  • G-Tek 3GX
  • Gray Dyneema Diamond
  • Gray Polyurethane Coated Palm
  • EN Cut Level 5
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4542C

EN 388 2016 Results: 4542CX

Abrasion: 4
Cut (Coupe Test): 5
Tear: 4
Puncture: 2
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

19-D330

  • G-Tek 3GX with Dyneema Diamond Technology
  • White Knit with Gray PU Palm and Fingertip Coating
  • EN Cut Level 5
  • SIZES: XS-3XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4542D

EN 388 2016 Results: 4542DX

Abrasion: 4
Cut (Coupe Test): 5
Tear: 4
Puncture: 2
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

19-D334

  • Dyneema Diamond Blend Seamless Knit
  • 13 Gauge
  • Salt & Pepper
  • Black Nitrile Foam Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4443C

EN 388 2016 Results: 4443CX

Abrasion: 4
Cut (Coupe Test): 4
Tear: 4
Puncture: 3
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Hi-Vis Seamless Knit Dyneema® Diamond Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

19-D340OR

  • Dyneema Diamond Blend Seamless Knit
  • 13 Gauge
  • Hi-Vis Orange
  • Black Nitrile Foam Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4544D

EN 388 2016 Results: 4544DX

Abrasion: 4
Cut (Coupe Test): 5
Tear: 4
Puncture: 4
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX®

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

19-D360

  • Dyneema Diamond Blend Seamless Knit
  • 13 Gauge
  • Gray
  • Gray Polyurethane Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: S-XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4442C

EN 388 2016 Results: 4442CX

Abrasion: 4
Cut (Coupe Test): 4
Tear: 4
Puncture: 2
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® 3GX® Black

Seamless Knit Dyneema® Diamond Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers - Touchscreen Compatible

19-D526B

  • Dyneema Black Diamond Seamless Knit
  • 13 Gauge
  • Black Polyurethane Grip
  • Palm & Fingertips
  • Touchscreen Compatible
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4543D

EN 388 2016 Results: 4543DX

Abrasion: 4
Cut (Coupe Test): 5
Tear: 4
Puncture: 3
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves

G-Tek® 3GX® Black

Seamless Knit Dyneema® Diamond Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers - DISCONTINUED

19-D534B

  • Dyneema Black Diamond Seamless Knit
  • 13 Gauge
  • Black Nitrile Foam
  • Now w/ DISCOUNTED PRICING!
  • SIZES: M-XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4543C

EN 388 2016 Results: 4543CX

Abrasion: 4
Cut (Coupe Test): 5
Tear: 4
Puncture: 3
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

SHOWING 1-13 OF 13 ITEMS
1 of 1
pin Rep Finder
Compare ()
Clear All Compare
Okay, Got it.
X

ORDER SAMPLE

X

GET FIELD TRIAL