Leaders in
Hand Protection
and PPE

BROWSE ALL PRODUCTS
SHOWING 1-36 OF 116 ITEMS
1 of 4
Cut Resistant Gloves

Kut Gard®

Seamless Knit ACP / PolyKor® Blended Glove with Polyester Lining - Heavy Weight

07-TW600

  • Aramid Engineered Blend 7 Gauge Seamless Knit Medium Wt Glove with Poly Lining
  • ANSI A6
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case
ansi-A6
ANSI Cut Level: A6

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

ansi-abrasion-2
ANSI Abrasion Level: 2

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

09-K1150

  • Polykor Seamless Knit
  • Yellow 13 Gauge Shell
  • Gray Polyurethane Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

3X41

EN 388 2016 Results: 3X41X

Abrasion: 3
Cut (Coupe Test): X
Tear: 4
Puncture: 1
Cut (TDM-100 Test):
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Latex Coated Crinkle Grip on Palm & Fingers

09-K1320

  • Glove
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

3X43C

EN 388 2016 Results: 3X43CX

Abrasion: 3
Cut (Coupe Test): X
Tear: 4
Puncture: 3
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Claw Cover Gloves

Claw Cover®

Seamless Knit PolyKor® Blended Glove with Polyester Lining - Medium Weight

14-ASP700

  • Engineered Antimicrobial Yarn
  • Gauge Seamless Knit
  • Medium Weight Cotton Lined
  • Gray
  • Silicone Free
  • SIZES: S-XL
  • PACKED: 6 Dozen/Case
ansi-A5
ANSI Cut Level: A5

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Claw Cover Gloves

Claw Cover®

Seamless Knit PolyKor® Blended Glove with Polyester Lining and Double-Sided PVC Dot Grip - Medium Weight

14-ASP700PDD

  • Engineered Antimicrobial Yarn
  • Gauge Seamless Knit
  • Medium Weight Cotton Lined
  • Double Sided PVC Grip
  • Gray
  • Silicone Free
  • SIZES: XXS-XL
  • PACKED: 12 Dozen/Case
ansi-A5
ANSI Cut Level: A5

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

Kut Gard®

Seamless Knit PolyKor® Blended Glove with Polyester Lining - Heavyweight

14-PK700

  • Polykor Engineered Yarn
  • 7 Gauge
  • Seamless Knit Glove Silicone Free
  • SIZES: S-XL
  • PACKED: 12 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves BEST SELLER

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

16-150

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Salt & Pepper
  • Gray Polyurethane Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • Silicone Free
  • SIZES: XXS-3XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X42B

EN 388 2016 Results: 4X42BX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 2
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 4

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers - Vend-Ready

16-150V

  • Salt & Pepper PolyKor Blended Shell
  • 13 Gauge
  • Gray Polyurethane Coated Smooth Grip
  • Palm and Fingertips
  • Silicone Free
  • Vend Ready
  • SIZES: XXS-3XL
  • PACKED: 72 Pair/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X42B

EN 388 2016 Results: 4X42BX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 2
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 4

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor® X7™

Seamless Knit PolyKor® X7™ Blended Glove with Nitrile Coated MicroSurface Grip on Palm & Fingers - Touchscreen Compatible

16-278

  • PolyKor Blend
  • 18 Gauge
  • Black
  • Black MS Nitrile Coated Silicone Free
  • Touchscreen
  • Reinforced Thumb
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A7
ANSI Cut Level: A7

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X42F

EN 388 2016 Results: 4X42FX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 2
Cut (TDM-100 Test): F
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Grip on Palm & Fingers - Vend-Ready

16-318V

  • PolyKor Blend Seamless Knit
  • 18 Gauge
  • Light Blue
  • Blue Polyurethane Coated Grip
  • Palm & Fingertips
  • Knit Wrist
  • Vend Ready
  • SIZES: XXS-2XL
  • PACKED: 72 Pair/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4342B

EN 388 2016 Results: 4342BX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 2
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor® X7™

Seamless Knit PolyKor™ X7™ Blended Glove with NeoFoam® Coated Palm & Fingers - Touchscreen Compatible

16-320

  • PolyKor Seamless Knit Shell
  • 18 Gauge
  • Light Blue
  • Blue NeoFoam Grip
  • Palm & Fingertips
  • Touchscreen Compatible
  • Knit Wrist
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X41B

EN 388 2016 Results: 4X41BX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 1
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves BEST SELLER

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

16-322

  • PolyKor Blend Seamless Knit
  • 18 Gauge
  • Light Blue
  • Blue Polyurethane Coated Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: XXS-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4342B

EN 388 2016 Results: 4342BX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 2
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Hi-Vis Seamless Knit PolyKor® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

16-323

  • PolyKor Blend Seamless Knit Shell
  • 15 Gauge
  • Hi-Vis Yellow
  • Gray Nitrile Foam Coated Grip
  • Reinforced Thumb Crotch
  • Silicone Free
  • SIZES: XS-3XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X31B

EN 388 2016 Results: 4X31BX

Abrasion: 4
Cut (Coupe Test): X
Tear: 3
Puncture: 1
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves NEW

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers - Touchscreen Compatible

16-328

  • PolyKor Blend Seamless Knit
  • 18 Gauge
  • Gray
  • Nitrile Coated Grip
  • Palm & Fingertips
  • Touchscreen
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X41B

EN 388 2016 Results: 4X41BX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 1
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-5
ANSI Abrasion Level: 5

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Double-Dipped Nitrile Coated MicroSurface Grip on Palm & Fingers

16-330

  • Seamless Knit Shell
  • 13 Gauge
  • Blue & White
  • Double Dipped
  • Black Nitrile Microsurface Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4342B

EN 388 2016 Results: 4342BX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 2
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Nitrile Coated MicroSurface Grip on Palm & Fingers

16-333

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Salt & Pepper
  • Nitrile Coated Grip
  • Palm & Fingertips
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X42C

EN 388 2016 Results: 4X42CX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 2
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

16-334

  • Seamless Knit Shell
  • 13 Gauge
  • Salt & Pepper
  • Black Nitrile Foam Grip
  • Palm and Fingertips
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4343B

EN 388 2016 Results: 4343BX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 3
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Hi-Vis Seamless Knit PolyKor® Blended Glove with Double-Dipped Nitrile Coated MicroSurface Grip on Palm & Fingers

16-340LG

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Hi-Vis Lime Green
  • Double Dipped
  • Black Nitrile Microsurface Grip Over Flat Nitrile
  • Knit Wrist
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4544C

EN 388 2016 Results: 4544CX

Abrasion: 4
Cut (Coupe Test): 5
Tear: 4
Puncture: 4
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Hi-Vis Seamless Knit PolyKor® Blended Glove with Double-Dipped Nitrile Coated MicroSurface Grip on Palm & Fingers

16-340OR

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Hi-Vis Orange
  • Double Dipped
  • Black Nitrile MicroSurface Grip Over Flat Nitrile
  • Knit Wrist
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X44C

EN 388 2016 Results: 4X44CX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 4
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Hi-Vis Seamless Knit PolyKor® Blended Glove with Double-Dipped Nitrile Coated MicroSurface Grip on Palm & Fingers

16-343LG

  • PolyKor Blend Seamless Knit Shell
  • 13 Gauge
  • Hi-Vis Lime Green
  • Double Dipped
  • Black Nitrile MicroSurface Grip Over Flat Nitrile
  • Knit Wrist
  • SIZES: XS-3XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4344B

EN 388 2016 Results: 4344BX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 4
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-5
ANSI Abrasion Level: 5

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Hi-Vis Seamless Knit PolyKor® Blended Glove with Double-Dipped Nitrile Coated MicroSurface Grip on Palm & Fingers

16-343OR

  • PolyKor Blend Seamless Knit Shell
  • 13 Gauge
  • Hi-Vis Orange
  • Double Dipped
  • Black Nitrile Microsurface Grip Over Flat Nitrile
  • Knit Wrist
  • SIZES: XS-XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4344B

EN 388 2016 Results: 4344BX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 4
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-5
ANSI Abrasion Level: 5

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended with Double-Dipped Nitrile Coated MicroSurface Grip on Palm & Fingers

16-350

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Salt & Pepper
  • Black Nitrile Microsurface Coated Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X43D

EN 388 2016 Results: 4X43DX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 3
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Nitrile Coated MicroSurface Grip on Palm ,Full fingers and knuckles

16-353-AP

  • G-Tek® CR
  • Salt & Pepper 13 Gauge PolyKor Blended Shell
  • Black Micro-Surface Nitrile Coated Palm
  • Full fingers and knuckles
  • SIZES: XS-XL
  • PACKED: 72 Pair/Case

4342

EN 388 2016 Results: 4342XX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 2
Cut (TDM-100 Test): X
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers

16-354

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Black
  • Black Nitrile Foam Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A5
ANSI Cut Level: A5

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X43E

EN 388 2016 Results: 4X43E

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 3
Cut (TDM-100 Test): E
Impact Protection:

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 4

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Nitrile Coated Foam Grip on Palm, Fingers & Knuckles

16-355

  • Seamless Knit Shell
  • 13 Gauge
  • Salt & Pepper
  • Black Nitrile Foam Grip
  • 3/4 Dip Palm Fingers & Knuckles
  • Knit Wrist
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A2
ANSI Cut Level: A2

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4343B

EN 388 2016 Results: 4343BX

Abrasion: 4
Cut (Coupe Test): 3
Tear: 4
Puncture: 3
Cut (TDM-100 Test): B
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-5
ANSI Abrasion Level: 5

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor® X7™

Seamless Knit PolyKor® X7™ Blended Glove with NeoFoam® Coated Palm & Fingers - Touchscreen Compatible

16-368

  • PolyKor X7 Blend Seamless Knit Shell
  • 18 Gauge
  • Burgundy
  • Black NeoFoam Coated Grip
  • Touchscreen Compatible
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X31C

EN 388 2016 Results: 4X31CX

Abrasion: 4
Cut (Coupe Test): X
Tear: 3
Puncture: 1
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 2

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers – Touchscreen Compatible

16-373

  • PolyKor Blend
  • 13 Gauge
  • Black
  • Black Foam Nitrile Coated Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A7
ANSI Cut Level: A7

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X43F

EN 388 2016 Results: 4X43FX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 3
Cut (TDM-100 Test): F
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-5
ANSI Abrasion Level: 5

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 4

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves BEST SELLER

G-Tek® PolyKor® X7™

Seamless Knit PolyKor® X7™ Blended Glove with NeoFoam® Coated Palm & Fingers - Touchscreen Compatible

16-377

  • PolyKor Blend w/ X7 Technology
  • 18 Gauge
  • Black
  • Black NeoFoam Coated Grip
  • Touchscreen Compatible
  • FDA 21 CFR Compliance
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A7
ANSI Cut Level: A7

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X42F

EN 388 2016 Results: 4X42FX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 2
Cut (TDM-100 Test): F
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® X7™ Blended Glove with Nitrile Coated Foam Grip on Palm & Fingers - Touchscreen Compatible

16-378

  • PolyKor Blend
  • 18 Gauge
  • Black
  • Black Foam Nitrile Coated Silicone Free
  • Touchscreen
  • Reinforced Thumb
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A7
ANSI Cut Level: A7

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X42F

EN 388 2016 Results: 4X42FX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 2
Cut (TDM-100 Test): F
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-5
ANSI Abrasion Level: 5

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves

G-Tek® PolyKor® X7™

Seamless Knit PolyKor® X7™ Blended Glove with NeoFoam® Coated MicroSurface Grip on Palm & Fingers - Touchscreen Compatible

16-399

  • PolyKor Blend w/ X7 Technology
  • 13 Gauge
  • Green
  • Black NeoFoam Coated Grip
  • Palm & Fingertips
  • Touchscreen Compatible
  • Silicone Free
  • SIZES: S-2XL
  • PACKED: 6 Dozen/Case
ansi-A9
ANSI Cut Level: A9

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X43F

EN 388 2016 Results: 4X43FX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 3
Cut (TDM-100 Test): F
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves

G-Tek® PolyKor®

Hi-Vis Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

16-520HY

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Hi-Vis Yellow
  • Hi-Vis Yellow Polyurethane Coated Smooth Grip
  • Palm & Fingertips
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4542C

EN 388 2016 Results: 4542CX

Abrasion: 4
Cut (Coupe Test): 5
Tear: 4
Puncture: 2
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

16-530

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Salt & Pepper
  • Gray Polyurethane Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • SIZES: XXS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X43C

EN 388 2016 Results: 4X43CX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 3
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers - Vend-Ready

16-530V

  • PolyKor Blend Seamless Knit Shell
  • 13 Gauge
  • Salt & Pepper
  • Gray Polyurethane Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • Vend Ready
  • SIZES: XS-2XL
  • PACKED: 72 Pair/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X43C

EN 388 2016 Results: 4X43CX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 3
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves

G-Tek® PolyKor®

Industry Grade Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers - Bulk Pack

16-533

  • PolyKor Blend Seamless Knit
  • Industry Grade
  • 13 Gauge
  • Salt & Pepper
  • Polyurethane Coated Smooth Grip
  • Palm & Fingertips
  • Silicone Free
  • SIZES: XS-2XL
  • PACKED: 6 Dozen/Case
ansi-A3
ANSI Cut Level: A3

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X41C

EN 388 2016 Results: 4X41CX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 1
Cut (TDM-100 Test): C
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 3

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Cut Resistant Gloves NEW

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers - 21 Gauge - Touchscreen Compatible

16-541

  • PolyKor Blend Seamless Knit
  • 21 Gauge
  • Black
  • Black Polyurethane Coated Flat Grip
  • Palm & Fingertips
  • Reinforced Thumb Crotch
  • Touchscreen
  • SIZES: XS-2XL
  • PACKED: 12 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

3X31D

EN 388 2016 Results: 3X31DX

Abrasion: 3
Cut (Coupe Test): X
Tear: 3
Puncture: 1
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-3
ANSI Abrasion Level: 3

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 2

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

Touchscreen Compatible

A common misconception is that touchscreens work based on heat from fingers. It's not heat that generates touchscreen functionality, instead, most screens work either on finger pressure applied or electrical field disruption. Basically, this means there are two main types of touchscreen technologies, Resistive and Capacitive.

Click here for more information about Resistive and Capacitive Touchscreens

Cut Resistant Gloves BEST SELLER

G-Tek® PolyKor®

Seamless Knit PolyKor® Blended Glove with Polyurethane Coated Flat Grip on Palm & Fingers

16-560

  • PolyKor Blend Seamless Knit
  • 13 Gauge
  • Gray
  • Gray Polyurethane Coated Smooth Grip
  • Palm & Fingertips
  • Knit Wrist
  • Silicone Free
  • SIZES: XXS-2XL
  • PACKED: 6 Dozen/Case
ansi-A4
ANSI Cut Level: A4

Test Method: ASTM F2992-15

New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

4X43D

EN 388 2016 Results: 4X43DX

Abrasion: 4
Cut (Coupe Test): X
Tear: 4
Puncture: 3
Cut (TDM-100 Test): D
Impact Protection: X

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ansi-abrasion-4
ANSI Abrasion Level: 4

Test Method: ASTM D3389-10

The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.

ANSI PUNCTURE LEVEL: 4

The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

Extended Life – Reusable/Launderable

Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.

SHOWING 1-36 OF 116 ITEMS
1 of 4
pin Rep Finder
Compare ()
Clear All Compare
Okay, Got it.
X

ORDER SAMPLE

X

GET FIELD TRIAL